NERO 3D HB

NERO 3D HB

NERO 3D HB

LIGHT ENGINE

DLP® Type:: 1 Chip DMDs 0,95” 1080p Resolution:: 1920x1080 pixels Brightness(2):: up to 3.000 Ansi Lumens (adjustable) Lens:: High quality, high resolution improved optics for higher contrast and better black level with motorized zoom and focus adj. Special features::SIM2 DynamicBlack Technology Enhanced Solution ::Puremotion 2D for fast action materials ::Puremovie 2D ::Motorized IRIS Control (MIC) Lamp power:: 280W dimmable to 230W Lamp life expectancy(1) :: 2.000 hours typical in standard power mode; 3.000 hours in ECO mode

INSTALLATION

Throw ratio standard lens:: 1.75-2.48:1 (type T2) Throw ratio optional lenses:: 1.37-1.66:1 (typ. T1) ::2.6-3.9:1 (typ. T3) Optical shift:: manual up half picture (+50%) and Digital keystone adjustment (for 2D and 3D 1080p24 modes) Picture size (inches diagonal):: 50-300 Aspect ratio:: 4:3, 16:9 Anamorphic, LetterBox, Panoramic, Pixel to Pixel + 3 custom-user adjustments

ELECTRONICS

Horizontal & vertical scan freq.:: 15-80kHz/48-120Hz SDTV:: PAL (B,G,H,I,M,N,60); SECAM; NTSC autom. selected HDTV:: 480p, 720p 50/60, 1080i 50/60, 1080p 24/50/60 + 576p PC graphic standard:: VGA, SVGA, XGA, SXGA, UXGA, WUXGA 10 bit Full Channel Signal Board Video Processing

INPUTS/OUTPUTS

Digital:: 2 x HDMI-HDCP vers. 1.4a Analog::1 x Graphic RGBVH (VGA-UXGA) (D-sub 15 pin) ::1 x Component - Analog YPbPr/RGBs/RGBHV (RCA) ::1 x Composite Video Control:: 3D Sync out ::1 x RS232 (D-sub 9 pin) ::1 x USB Miscellaneous::3 x 12V 100mA output (via Jack)

GENERAL SPECIFICATIONS

Software control:: upgradable via RS232, serial interface or USB Mains voltage range:: 100-240 +/-10% (48/62 Hz) Power consumption (max.):: 300 W Projector dimensions (WxHxD):: 458 x 210 x 455 mm (18”x8.3”x17.9”) Projector Weight:: 11 Kg. or 24.3 lbs

ACCESSORIES

Supplied::Installation and User Manual ::AC power cords (2m - 6.6 ft) ::Backlit remote control and batteries ::Live Colors Calibration software 2.0 Optional::SIM2 VISUS Active Glasses ::IR Emitter ::Projector ceiling bracket ::Anamorphic lens systems (fixed or motorized) (1)Lamp life: the hours quoted have been measured in a lab under ideal test conditions. Lamp life varies depending on usage conditions and the surrounding environment. This is an average value that cannot be guaranteed and is not protected by warranty. (2)ANSI Lumen Specification: This is the typical projector brightness specification found in most sales literature. This measurement allows for direct comparison with other manufacturer’s projectors. Measurements are taken in a totally dark test room with T3 type lens (wide angle zoom settings), brand new lamp at full power, lamp’s native white color temperature, internal test pattern (full white) and in compliance with ANSI IT7.228-1997 specification. The DLP® logo and DLP® medallion are trademarks of Texas Instruments. product specifications are subject to change without notice. Due to constant product development, specifications and design might be subject to change without notice.